Duck Boat Paint and Primer

I only have experience with FME, it took a real beating in the ice, and did not scratch, chip or wear. The only place it wore is where it was covering 5200, and did not adhere well there, but what would!
 
FME from Lou at Lock, Stock & Barrell.
FME means Freakin' Miracle Enamel
 
On bare aluminum I used etching primer then Home depo exterior latex (color matched the camo colors I wanted). This fall will be 6 years and the paint is still there with no issues to date.
My boat is used 80% of the time in the salt.
 
Last edited:
Here's some info that might help you decide.
Let me know how we can be of service.
Lou


Painting an Aluminum or Fiberglass Boat
  1. Be sure the boat has been cleaned off well with soap and water to remove all dirt, grease, leaves, grime and all that stuff that accumulates from years of hunting.
  2. Lightly solvent wipe things down with a rag and lacquer thinner. This will remove any gasoline, oil or petroleum residues that would mess with your sanding or prevent paint from adhering. When finished with the solvent rag, be sure to let it set out and lose it’s solvents before you put it into a closed container or trash can.
  3. Sand the entire boat, as required, to remove and/or scuff all the paint. Be sure to remove any loose paint. When sanding a duck boat, I prefer 80-100 grit. It gives better “tooth” and, after all……..it’ll help with the dulled surface and paint adhesion. Sanding must be taken into the best previously adhered surface in order to have the new coat of paint hold properly.
  4. For Aluminum boat-Spot prime any bare aluminum with ASG Primer (or AG Primer), specifically designed for use on “Aluminum, Stainless & Galvanized”. Do not thin AG Primer. A second option would be to prime the entire boat with PPG’s Epoxy Primer.
  5. For Fiberglass boat-You can go right to the FME as this is a Primer-Based Paint and will serve as its own primer. If you would like, another option would be to prime with PPG-Epoxy Primer and then follow up with FME.
  6. Once the primer has dried (AG, PPG or 1st coat of FME), you can base coat the entire boat, inside and out, with the base coat FME (Flat Marine Enamel-oil based) color of your choice. FME is a “primer-based” paint and requires no other primer underneath it on a properly prepared surface. You may use a brush, roller or sprayer. When spraying, the best is an airless sprayer though you can thin slightly with a high quality paint thinner for use in a regular air spray gun. If using the air-feed spray gun, we recommend the top-feed, gravity style of gun. It requires less air and less thinning to get a proper pattern. You will also achieve greater success with a couple thinner coats rather than one thick coat. Thinner coats will cure/dry much faster and more thoroughly….thus, more durable. Secret: “thin, you win”.
  7. When the base coat is dry (usually overnight in good temps), you may accent with any other FME color you’d like. The options are endless……match your local vegetation.
  8. We have several camouflage patterned paint schemes and colors available.
*Our 2-tone Reed Stripe was developed for the cat-tail marshes & flooded corn. Base coat in Starcraft Camo Light Brown (#26) and reed stripe with an automotive striping brush with Starcraft Camo Dark Brown (#27), thinning #27 on the palette as you work. We developed these colors through PPG specifically for us and Starcraft. You can even “green it up” a bit with Dead Grass Green (#28), O/D Green (#35) or some Olive (#18).
*Our Open Water Gray Pattern is very effective for layout hunting. You can base coat the entire boat with Open Water Medium Gray (#33) or Open Water Dark Gray (#34) and allow it to dry. Once dry, overstripe with a wave pattern of Open Water Light Gray (#32) by cutting the feed pressure down, reducing the size of your pattern to a small area and reducing the feed rate so it will be easy to control. Move the spray gun around in a lazy “wave”, walk alongside the boat and “wave” the gun to give the pattern you’d like.
We have pictures of these patterns that we can email to you.
  1. You can create your own color patterns/schemes with any of the FME colors we have. All the decoy and boat paints are TRUE - FLAT MARINE ENAMELS and work well with each other. We also do custom colors at no extra cost…try us.
Lock Stock & Barrell, Inc.​
123 Avery (shop)​
Clinton Twp., MI 48036​
Ofc.Ph: (586) 790-2678, Shop Ph: (586) 465-0339​
 
I used FME. Sanded glass, thinned FME a little and gave a good coat. Dried for 2 days and put straight FME. No peeling top or bottom. Tried aluminum, but did not prime. Sanded lite, wiped with thinner, painted with thinned FME and a coat of regular FME. Works so far, but don't use it much.
 
I would also highly recommend Lock Stock and Barrel FME
I put a hole in my DW-15 and Lou had an exact color match. Glass repair is a little "rough" but the paint matched perfectly.
 
I've painted 4 boats with Lou's product. Each one still has the original paint. Had to touch up wear area where stuff rubs and where I stand. Other than this minor wear the stuff is bulletproof.

I've sprayed 3 boats and rolled and brushed one. Should you decide to spray, have Lou provide guidance on viscosity you want in your sprayer. I used a Harbor Freight $10 HVLP and while I had to refill the cup a few times it worked great.

Mark
 
Last edited:
Still having problems with the website;

Here are the links to our FME Color Chart and our Catalog.

FME Color Chart: http://www.rccd.org/Documents/2017_documents/FME-LSB-140121.pdf

Catalog: http://www.rccd.org/Documents/2017_documents/LSB-CAT-1707.pdf

Our website is down right now (hacked) but I'm hosting the FME Chart & Catalog on another site I manage for our model airplane flying club (www.rccd.org)
Holler with any questions and let me know how we can be of service.
Lou Tisch

Might have to copy and paste into your browser.
 
You must log in or register to reply here.
Back
Top