Dave Parks
Well-known member
Here's what I was telling you about this morning. Boni showed up at noon yesterday and we had all four corners of the flight pen braced by 4:30. We used 4x4's for the "H" braces and these ratchets on the New Zealand wire.
A fence staple holds teh NZ wire in place while it's tightened at a 45 degree angle. You can also see the back end of the re-bar. The holes are pre-drilled in the post and "H" brace, then the re-bar is poubded into them with a 3# hammer.
Each corner is done this way so that I can put a lot of pull on the long NZ wires that run atop the posts from one end to the other. This will give support to the top netting and also a place to connect both teh top netting and teh top of the 72" tall chicken wire between the vertical posts.
Due to the un-even ground, teh next step is to pull a line from on end to the other at 5'6" and then cut off all the excess height of the posts with the Saws-All. Then I will install the top NZ wire down the tops of the posts inside fence staples and put a NZ ratchet on either end and tighten the wire. Nezt will go the 72" chicken wire on the outside with teh excess turned out flat onto the ground. Then 2X6's will be nailed to the outside of the post on the bottom and the chicken wire will be stapled to them from the inside as well as the posts on the outside. Over that will go the heavy 4' garden fencing with the 2x3" mesh. This will keep out everything but a bear and I don't expect too much trouble from them with all the electric fencing wires that go over the outside of the pen. (wish I had 220V up there right now!) A lot of horizontal heavy mesh fencing will go underground around teh pen to prevent animals from trying to did under the pens. Mac says the first 60 days are prblematic then they seem to give up. The top netting goes on last and then the pen will be ready for the birds.
I'm taking notes and photo's as I go along. While talking to the publisher of the Game Bird and Conservation Gazette he asked me to do a photo essay on the building of the flight pen for their magazine, if all turns out well I may do it. I just hope they could live with my poor spelling and typo's :^)
Dave
A fence staple holds teh NZ wire in place while it's tightened at a 45 degree angle. You can also see the back end of the re-bar. The holes are pre-drilled in the post and "H" brace, then the re-bar is poubded into them with a 3# hammer.
Each corner is done this way so that I can put a lot of pull on the long NZ wires that run atop the posts from one end to the other. This will give support to the top netting and also a place to connect both teh top netting and teh top of the 72" tall chicken wire between the vertical posts.
Due to the un-even ground, teh next step is to pull a line from on end to the other at 5'6" and then cut off all the excess height of the posts with the Saws-All. Then I will install the top NZ wire down the tops of the posts inside fence staples and put a NZ ratchet on either end and tighten the wire. Nezt will go the 72" chicken wire on the outside with teh excess turned out flat onto the ground. Then 2X6's will be nailed to the outside of the post on the bottom and the chicken wire will be stapled to them from the inside as well as the posts on the outside. Over that will go the heavy 4' garden fencing with the 2x3" mesh. This will keep out everything but a bear and I don't expect too much trouble from them with all the electric fencing wires that go over the outside of the pen. (wish I had 220V up there right now!) A lot of horizontal heavy mesh fencing will go underground around teh pen to prevent animals from trying to did under the pens. Mac says the first 60 days are prblematic then they seem to give up. The top netting goes on last and then the pen will be ready for the birds.
I'm taking notes and photo's as I go along. While talking to the publisher of the Game Bird and Conservation Gazette he asked me to do a photo essay on the building of the flight pen for their magazine, if all turns out well I may do it. I just hope they could live with my poor spelling and typo's :^)
Dave